Note: This model only available in 380-415 volt three-phase.
Across International's IHL series 1 kHz to 20 kHz low frequency induction heaters are good for a wide range of applications including deep heat penetration for full hardening processes, steel rod forging, tempering of pressing dies, pre-heating for welding, and melting of metal batches over 2 kilogram. They are not limited to ferromagnetic materials, so nonferrous metals can also be used effectively.
There are three major components to the system: the power supply, the compensating capacitor/transformer and the induction coil/smelting crucible. Our heaters automatically adjust to the best resonant frequency in order to achieve the most efficient overall heating results based on our customer's requirements which include heat penetration, heating efficiency, operating noise and electromagnetic homogeneity. Two of our most popular low frequency machines are the Melting Furnaces with Tile-Pour Melter and Auto-feeding Rod Heating Furnaces for Forging.
Dual-station with connection cables and hose let you separate the heater and controller up to seven feet, allow you to stay away from high temperature, dirty and corrosive environment and for a safer operation, or if you need to move the heater to your work pieces constantly during operation.
Ease of use: just plug in the power and connect the water cooling system. Our simple instruction allows you to use the heater in 15 minutes.
Relatively light weight, portable, instant heat and up to 90% energy savings.
Procise control with digital output, frequency and current displays.
Remote foot switch for safer operation.
Dual automatic and manual modes.
Optional graphite, MgO and SiO2 crucibles available. (melting material decides crucible type, weight and size of the material decide crucible size)
Custom coil design available (fixed coil or coil on a cable so it can be used like a wand)
ISO 9001:2008 registered manufacturer.
Overvoltageprotection: machine shuts down when input voltage is over 500V. Overvoltage light will turn on and buzzer will sound continuously. Alarm and light shut off automatically when voltage goes below 500V.
Overheatprotection: if sensor detects heat radiator temperature is over 55°C, machine will shut down, overheat light will turn on and buzzer will sound continuously. Increase water pressure or lower water temperature until alarm goes off itself.
Overcurrent/malfunction protections: machine will shut down, indicator light turned on and buzzer sounds continuously if one of these situations occurs:
One of the machine parts becomes overheated
Interfering signal detected
Short circuit between work pieces and induction coils
Induction coils touching each other
Input voltage is too low
Low water pressure protection: if water pressure goes below 29 PSI, machine will shut down, water protection light will turn on and buzzer will sound continuously.
Always wear protective gear and goggles when operating the machine. Crucibles must be covered all the time during operation. Across International is not responsible for any injury or damage caused by misuse.
Do not run no-load operation for a long period of time, it might cause damage to the machine.
Circulating water must be pure, clean and below 45°C.
Machine must be grounded properly all the time during operation.
Do NOT use single-turn coil if coil diameter is smaller than 100 mm, it will cause high frequency damage to the machine.
Thread tape (or related material) is absolutely prohibited during installation of induction coils.
Max. input current
108 A (120A 3-phase circuit breaker required)
380-415 VAC 50/60Hz three phase
Max. oscillating/input power
100% (24 hours continuous working)
≥ 0.2 Mpa (29 PSI) you may use tap water and water pump (>1/4HP & >240 Gph)
> 6 liters per minute
Power supply: 75 kg, 760 x 410 x 860 mm Transformer: weight and size depend on type and size of work pieces, and also heating requirements
IHL70 induction heater
Power cable btw power supply & capacitor x 1 Temp cable btw power supply & capacitor x 1 Water cooled cable btw capacitor & coil x 2
Remote on/off switch
Optional copper tubing induction coil made according to customer's requirements